Important Plumber Insights for Installing a Bathtub
Important Plumber Insights for Installing a Bathtub
Blog Article
Everyone has their private idea involving Tools You Need to Install a New Bathtub .
Installing a tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately tough job. If the old bathtub is easily available, the task can move speedily; if you need to open a wall to get rid of the old tub and also position the brand-new tub, the job is a lot harder. In either case, the task is within a residence handyman's skills, although you will require an assistant to move out the old tub as well as set in the new one. Make certain you have actually certified on your own for the work as well as fit attempting it. Rather than working with a contractor to take control of a halfway-completed task, it is far better to think about utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube connections.
This article will certainly help you install a brand-new bathtub in your washroom if you have currently purchased a brand-new bathtub and don't need to transform the setup of your previous water system pipelines.
Your devices and also product checklist should make up the following:
Preparing for the Setup
Firstly, the sustaining structure supplied with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps system to prevent strain on the bathtub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you use every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its final placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, then the first thing you ought to do is disconnect the water system. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the limited accessibility that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the remaining water that will originate from the pipes. As soon as the supply pipelines have actually been gotten rid of, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Before carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Using both wooden boards under its feet, position the tub in the called for setting. The wood boards are handy in uniformly spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little factors.
The next objective is to guarantee that the tub is leveled all round. This can be attained by examining the level as well as changing the feet on the bath tub until the level reads degree.
To install taps, fit all-time low of the outermost versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other tap.
Turn on the water and also check all joints and new pipework for leaks and tighten them if required. Fill the bathtub and also check the overflow electrical outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bath tub needs to wait till the bath tub has actually been utilized a minimum of when as this will certainly settle it right into its final placement.
Suitable New Touches
If the tails of the new taps are plastic, after that you will need a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin ensuring that the washers are in place between the faucet and also the sink. Secure the tap in place with the producer supplied backnut. When the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical tap ports. The previous type needs to be connected to the tap finishes first, tightening up only by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to fracture a rigid seal, triggering the water to penetrate the wall in between the bathroom and also the tiling, resulting in issues with wetness and possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes and cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water before sealing, to enable the movement experienced when the bathtub remains in use. The sealer can break relatively very early if you do not consider this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently available on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was made aware of that write-up on Installing A Bathtub through a friend on another web property. Sharing is good. You never know, you may be helping someone out. We thank you for reading our article about Installing A Bathtub.
Best decision? Call us. Report this page